Identifying dispersive (sodic) soils

Page last updated: Tuesday, 16 March 2021 - 3:30pm

Please note: This content may be out of date and is currently under review.

It is not always easy to identify the degree of dispersion or sodicity in soils. The choice of suitable management depends on knowing the soil sodicity and whether dispersion is a problem. This page provides several ways of identifying dispersive soils.

Sodic soils are common in the south-west agricultural area of Western Australia, where they occur mainly as duplex or gradational profiles. Sodic duplex soils are particularly susceptible to dispersion and waterlogging, because they are commonly on broad, flat landscapes with poor drainage.

What is a dispersive soil?

In a dispersive soil, the soil aggregates (small clods) collapse when the soil gets wet by fresh water, because the individual clay particles disperse into solution. This collapse of structure causes the soil to slump, lose porosity and become denser, thus restricting root growth of most plants.

What is a sodic soil?

A sodic soil is defined as a soil with an exchangeable sodium of greater than 6% of the cation exchange capacity. Non-saline sodic soils are usually dispersive in the presence of fresh water. Saline-sodic clays are less dispersive than non-saline-sodic soils and have higher infiltration rates. Many sodic clays may still produce wheat yields near their rainfall-limited yield potential, where the salt levels in the soil solution are higher than the critical flocculation concentration, but are not toxic to plants.

Identifying sodic or dispersive soils

There are 3 ways to identify dispersive soils:

  • measure the exchangeable sodium percentage (ESP) as part of a standard soil test (measures sodicity)
  • use a simple soil dispersion test
  • observe visual indicators of moderate or severely dispersive topsoils.

Measure the exchangeable sodium percentage

The exchangeable sodium percentage (ESP) measures the proportion of cation exchange sites occupied by sodium. Soils are considered sodic when the ESP is greater than 6, and highly sodic when the ESP is greater than 15 (Table 1).

Table 1 Relationship between degree of dispersion and exchangeable sodium percentage
Rating Exchangeable sodium percentage Soil dispersion test
Non-sodic <6 No dispersion evident after 24 hours. Aggregates slaked but not dispersed (milky) clay.
Slightly sodic 6–10 Dispersion (milky halo) evident after 24 hours. Soil aggregates slightly disperse.
Moderately sodic 6–10 Dispersion (milky halo) evident after several hours. Soil aggregates partially disperse.
Highly sodic >15 Dispersion (milky halo) evident in less than 30 minutes. Soil aggregates completely disperse.

Back to top

Use a simple soil dispersion test

The dispersive behaviour of a soil indicates the level of sodicity (Figures 1 and 2). The procedure for a soil dispersion test is:

  • collect dry soil aggregates (crumbs of soil) from different depths in a soil profile (Figure 1)
  • place the soil aggregates into a clear jar of distilled water, taking care not to mix or agitate the soil.

Aggregates will often, but not always, slake (crumble) soon after being placed in the water; however, this is not dispersion.

The water around the edges of the soil aggregate in a dispersive soil will become cloudy and milky looking (water looks dirty) because of the dispersed clay (Figures 1 and 2).

For a highly dispersive soil, dispersion will be obvious after about 10-30 minutes; for a moderately dispersive soil, it may take 2 hours for dispersion to be obvious (Figures 1 and 2).

Photograph of dispersion of soil samples from different depths in a soil profile, at ten minutes and ninety minutes
Figure 1 Dispersion test on samples at different depths in a soil profile at 10 minutes (left) and 90 minutes (right)
Four petri dishes of soil samples show nil dispersion through to severe
Figure 2 Degrees of soil dispersion (nil to severe) for soils that are non-sodic to highly sodic (from left to right)

Back to top

Observe visual indicators of moderate or severely dispersive topsoils

Obvious indicators in the field are:

  • soil is prone to becoming boggy when wet because of structural instability
  • milky coloured water ponds on the soil surface after rain
  • water infiltrates into the soil slowly
  • soils are prone to water erosion
  • soils are hard-setting and form a surface crust when dry
  • cracks can appear in some dispersive soils as the soil shrinks on drying.

Dispersive soils are susceptible to water erosion. Dispersive soils used for dam walls are very susceptible to tunnel erosion, and these dam walls often fail if there is a sudden inflow of fresh water.

Toxicities in dispersive (sodic) soils

While some dispersive soils can be acidic, the majority of dispersive soils in the Western Australian grainbelt are strongly alkaline with soil pHCa greater than 8.5. These strongly alkaline dispersive soils can also contain high concentrations of salt and boron. High boron levels are toxic to some crops and pastures and can reduce yields.

Salt tends to reduce the dispersive behaviour of soil, and dispersion may only be seen in saline soils when the soil is disturbed or large amounts of fresh water dilute the salt. Dispersion may be completely prevented in highly saline soils despite a high percentage of exchangeable sodium.

Contact information

Tim Overheu
+61 (0)8 9892 8533
+61 (0)8 9083 1142
Jeremy Lemon
+61 (0)8 9892 8413